How to Install a Bathtub ( Guide).
Contact UsThis article in the next paragraphs relating to Installing A Bathtub is indeed enjoyable. Check it out for yourself and see what you think of it.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently available, the task can relocate quickly; if you have to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the task is a lot harder. In either situation, the task is within a residence handyman's skills, although you will require an assistant to vacate the old tub and also embeded in the new one. Ensure you have qualified on your own for the work and also fit attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This post will certainly aid you mount a brand-new bath tub in your bathroom if you have actually currently acquired a new bathtub and don't need to change the arrangement of your previous water supply pipes.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be rather troublesome because of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be connected to the tap finishes first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Making use of the two wooden boards under its feet, position the bathtub in the needed position. The wooden boards are handy in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water system and also check all joints and new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait till the tub has been utilized a minimum of when as this will certainly resolve it right into its last placement.
Planning for the Installment
To start with, the sustaining frame supplied with the bath should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, causing the water to pass through the wall between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very fascinated by How to Install a Bathtub Yourself and I'm hoping you enjoyed the post. Sharing is nice. Helping others is fun. Thank you for your time. Visit again soon.
Schedule Your Job Now